caa a22 4500 445361891 CHVBK 20180317142917.0 cr unu---uuuuu 170323e20111201xx s 000 0 eng 10.1007/s11071-011-9953-1 doi (NATIONALLICENCE)springer-10.1007/s11071-011-9953-1 Nonstructural geometric discontinuities in finite element/multibody system analysis [Elektronische Daten] [Ashraf Hamed, Ahmed Shabana, Paramsothy Jayakumar, Michael Letherwood] Existing multibody system (MBS) algorithms treat articulated system components that are not rigidly connected as separate bodies connected by joints that are governed by nonlinear algebraic equations. As a consequence, these MBS algorithms lead to a highly nonlinear system of coupled differential and algebraic equations. Existing finite element (FE) algorithms, on the other hand, do not lead to a constant mesh inertia matrix in the case of arbitrarily large relative rigid body rotations. In this paper, new FE/MBS meshes that employ linear connectivity conditions and allow for arbitrarily large rigid body displacements between the finite elements are introduced. The large displacement FE absolute nodal coordinate formulation (ANCF) is used to obtain linear element connectivity conditions in the case of large relative rotations between the finite elements of a mesh. It is shown in this paper that a linear formulation of pin (revolute) joints that allow for finite relative rotations between two elements connected by the joint can be systematically obtained using ANCF finite elements. The algebraic joint constraint equations, which can be introduced at a preprocessing stage to efficiently eliminate redundant position coordinates, allow for deformation modes at the pin joint definition point, and therefore, this new joint formulation can be considered as a generalization of the pin joint formulation used in rigid MBS analysis. The new pin joint deformation modes that are the result of C 0 continuity conditions, allow for the calculations of the pin joint strains which can be discontinuous as the result of the finite relative rotation between the elements. This type of discontinuity is referred to in this paper as nonstructural discontinuity in order to distinguish it from the case of structural discontinuity in which the elements are rigidly connected. Because ANCF finite elements lead to a constant mass matrix, an identity generalized mass matrix can be obtained for the FE mesh despite the fact that the finite elements of the mesh are not rigidly connected. The relationship between the nonrational ANCF finite elements and the B-spline representation is used to shed light on the potential of using ANCF as the basis for the integration of computer aided design and analysis (I-CAD-A). When cubic interpolation is used in the FE/ANCF representation, C 0 continuity is equivalent to a knot multiplicity of three when computational geometry methods such as B-splines are used. C 2 ANCF models which ensure the continuity of the curvature and correspond to B-spline knot multiplicity of one can also be obtained. Nonetheless, B-spline and NURBS representations cannot be used to effectively model T-junctions that can be systematically modeled using ANCF finite elements which employ gradient coordinates that can be conveniently used to define element orientations in the reference configuration. Numerical results are presented in order to demonstrate the use of the new formulation in developing new chain models. Springer Science+Business Media B.V., 2011 Geometric discontinuities nationallicence Finite element nationallicence Multibody systems nationallicence B-spline nationallicence NURBS nationallicence Hamed Ashraf Department of Mechanical and Industrial Engineering, University of Illinois at Chicago, 842 West Taylor Street, 60607, Chicago, IL, USA aut Shabana Ahmed Department of Mechanical and Industrial Engineering, University of Illinois at Chicago, 842 West Taylor Street, 60607, Chicago, IL, USA aut Jayakumar Paramsothy U.S. Army RDECOM-TARDEC, 6501 E. 11 Mile Road, 48397-5000, Warren, MI, USA aut Letherwood Michael U.S. Army RDECOM-TARDEC, 6501 E. 11 Mile Road, 48397-5000, Warren, MI, USA aut Nonlinear Dynamics Springer Netherlands 66/4(2011-12-01), 809-824 0924-090X 66:4<809 2011 66 11071 https://doi.org/10.1007/s11071-011-9953-1 text/html Onlinezugriff via DOI 1 research-article jats NATIONALLICENCE 856 40 https://doi.org/10.1007/s11071-011-9953-1 text/html Onlinezugriff via DOI NATIONALLICENCE 700 1- Hamed Ashraf Department of Mechanical and Industrial Engineering, University of Illinois at Chicago, 842 West Taylor Street, 60607, Chicago, IL, USA aut NATIONALLICENCE 700 1- Shabana Ahmed Department of Mechanical and Industrial Engineering, University of Illinois at Chicago, 842 West Taylor Street, 60607, Chicago, IL, USA aut NATIONALLICENCE 700 1- Jayakumar Paramsothy U.S. Army RDECOM-TARDEC, 6501 E. 11 Mile Road, 48397-5000, Warren, MI, USA aut NATIONALLICENCE 700 1- Letherwood Michael U.S. Army RDECOM-TARDEC, 6501 E. 11 Mile Road, 48397-5000, Warren, MI, USA aut NATIONALLICENCE 773 0- Nonlinear Dynamics Springer Netherlands 66/4(2011-12-01), 809-824 0924-090X 66:4<809 2011 66 11071 Metadata rights reserved Springer special CC-BY-NC licence nationallicence BK010053 XK010053 XK010000 NATIONALLICENCE NATIONALLICENCE NL-springer